Toyota Trucks

Hi all.  I just installed a new tonneau cover on my 2002.  I recommend
Sportmasters hinged cover.  It runs about the same cost as a standard soft
cover, but it is hinged in the middle.  If you need to access something that
has slid to the back of the bed, rather than unsnapping the cover to get at it,
just flip a latch, and the whole cover frame tilts up on pistons.  Check out
www.sportmaster.com for more information or e-mail me at Mjd…@aol.com

Mike

The power rear window will only go down
3/4 the way and it goes down with a creaking sound at a slight angle,
has anyone had this problem? and what did it
cost to fix. Thanks for the help

Just changed my front rotor and brake pads on my toyota rav4 97 and now they
creak and not just a little bit, trust me…  I’ve rounded the end.  Any
other tips???  Someone tell me silicone hight temp (orange) between pads and
calipper…  The rotors and pads are "jobber"  My last try will be OEM
parts…

I was driving my 2001 Highlander today in about 95-100 degree temperature
when the air conditioner fan quit blowing.  There was still cold air coming
out of the vents but I could   not get the fan to blow.  After I got home
and let the vehicle cool down the AC fan started working again.

Does anybody have any input on what may be the cause of this behavior.

Wow!  How in the heck does one get that sucker out?  Skid plate
removal?!   Hmmmmm.

Needs some motor work. It cranks and runs but when you let off gas it goes
dead.. needs front grill and driver side front fender panel.. got pix if ya
want to take a look and make me an offer email me and I will send them to
ya..

TIA

Jackal

Anyone ever swapped seats in their runner?
I have the cloth seats with no power options, but would love the power
drivers seat with more options,
anyone know how tough it might be to switch, can I just unbolt the old and
plug and bolt in in the new seat?  (hopefully)
anyone know were I could get a different seat?
I’m looking for a power drivers seat in cloth Tan colored interior  (don’t
want leather)

thanks
Dave

I installed the TRD flares aftermarket on my 96 SR5 Taco… On the
rear drivers side I sort of flubbed the job and now it is not adhering
near the gas tank door.

The short radius of the curves made it a little tricky to get the
rubber trim aligned correctly. Anyone have any advice on how to do
this? (I am going to have to reorder the trim and redo the
installation).

Any idea what Toyota wants for the trim strip?

If anyone has a copy of the TSB I would like to see that too – I am
curious to know if it outlines any "tricks" to getting the trim to
align correctly.

Thanks to all,

J.

I’d like to find out what speakers will fit in my 4Runner before I rip
the doors open – can someone tell me what the largest speakers are that
will fit in the front and rear doors? It looks like there are probably
6.5′s in the front and 4.25′s in the rear judging by the grilles, but I
was able to replace the OEM 4.25′s with 6.5′s in my old Celica and MR2,
so I’m wondering if I can do the same with these.

While I’m at it, if anyone has any tips on lock-securing a sub box in
the rear, that would be great. I have a good alarm installed now, but
I’m still not wild about letting a box sit unsecured.

Thanks!
_____________________
w h i t   g u r l e y
whitgur…@R-E-M-O-V-E-T-H-I-Shotmail.com

My 1990 pickup truck had gear oil leaking from the joint of drive
shaft with the differential. How can I fix it ?
  LOUIS